Toggle navigation
Home
KPSC Previous Question Papers
Article Category
kerala psc
upsc
General
Popular Pages
Multiple Choice Question in കറന്റ് അഫയേഴ്സ് മേയ് 11
Multiple Choice Question in കറന്റ് അഫയേഴ്സ് - ഏപ്രില് 07
Multiple Choice Question in current-affairs-2016-12-22
Multiple Choice Question in current-affairs-2017-01-22
Multiple Choice Question in biochemistry-structure-and-properties-of-peptides
Multiple Choice Question in കറന്റ് അഫയേഴ്സ് - ക്വിസ് | ഡിസംബര് 05 - 12
Multiple Choice Question in biochemical-engineering-fluid-flow
Multiple Choice Question in biochemistry-allosteric-effects
Multiple Choice Question in current-affairs-2017-05-07
Multiple Choice Question in കറന്റ് അഫയേഴ്സ് മേയ് 26
Question Answer Bank
Multiple Choice Question Bank
Question Answer Category
Multiple Choice Question Category
Home
->
Multiple Choice Questions
Question Set
civil engineering strength of materials
1. The shear stress at any section of a shaft is maximum
(A): at a distance 3/4 r from the centre
(B): at a distance r/2 from the centre
(C): at the centre of the section
(D): at the top of the surface
(E): none of these.
Previous Question
Show Answer
Next Question
Add Tags
Report Error
Show Marks
Ask Your Doubts Here
Type in
(Press Ctrl+g to toggle between English and the chosen language)
Post reply
Comments
Show Similar Question And Answers
QA->Decrease of viscosity with increasing shear rate is known as....
QA->In a two roll mill the shear rate is adjusted by....
QA->Which type of gear permits lower position of propeller shaft?....
QA->In an automobile gear transmission the counter shaft drive gear is meshed with the gear on the:....
QA->In order to promote growth and investment, a new provision has been inserted in the Income-tax Act with effect from FY 2019-20 which allows any domestic company an option to pay income-tax at the rate of __ per cent subject to condition that they will not avail any exemption/incentive.?....
MCQ->The maximum shear stress in a solid shaft of circular cross-section having diameter d subjected to a torque T is τ. If the torque is increased by four times and the diameter of the shaft is increased by two times, the maximum shear stress in the shaft will be....
MCQ->Consider the following statements : 1. In a member subjected to uniaxial tensile force the maximum normal stress is the external load divided by the maximum cross-sectional area. 2. When the structural member is subjected to uniaxial loading, the shear stress is zero on a plane where the normal stress is maximum. 3. In a member subjected to uniaxial loading, the normal stress on the planes of maximum shear stress is less than the maximum. Of these statements :....
MCQ->Consider the following statements : In a uni-dimensional stress system, the principal plane is defined as one on which the 1. shear stress is zero. 2. normal stress is zero. 3. shear stress is maximum. 4. normal stress is maximum. Of these statements :....
MCQ->A shaft is subjected to a maximum bending stress of 80 N/mm2 and maximum shearing stress equal to 30 N/mm2 at a particular section. If the yield point in tension of the material is 280 N/mm2 and the maximum shear stress theory of failure is used, then the factor of safety obtained will be....
MCQ->The average shear stress in the hollow shaft is smaller than the average shear stress in the solid shaft.....
×
×
Type The Issue
×
Your Marks
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use | Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...
Privacy
|
Terms And Conditions
Question ANSWER With Solution