Toggle navigation
Home
KPSC Previous Question Papers
Article Category
kerala psc
upsc
General
Popular Pages
Multiple Choice Question in കറന്റ് അഫയേഴ്സ് മേയ് 11
Multiple Choice Question in കറന്റ് അഫയേഴ്സ് - ഏപ്രില് 07
Multiple Choice Question in current-affairs-2016-12-22
Multiple Choice Question in current-affairs-2017-01-22
Multiple Choice Question in biochemistry-structure-and-properties-of-peptides
Multiple Choice Question in കറന്റ് അഫയേഴ്സ് - ക്വിസ് | ഡിസംബര് 05 - 12
Multiple Choice Question in biochemical-engineering-fluid-flow
Multiple Choice Question in biochemistry-allosteric-effects
Multiple Choice Question in current-affairs-2017-05-07
Multiple Choice Question in കറന്റ് അഫയേഴ്സ് മേയ് 26
Question Answer Bank
Multiple Choice Question Bank
Question Answer Category
Multiple Choice Question Category
Home
->
Multiple Choice Questions
Question Set
1. A pull of 20 t is suddenly applied to a road of cross-sectional area 40 cmThe stress produced in the rod is equal to:
(A): 0.5 t/cm2
(B): 1.0 t/cm2
(C): 2.0 t/cm2
(D): 4 t/cm2
Previous Question
Show Answer
Next Question
Add Tags
Report Error
Show Marks
Ask Your Doubts Here
Type in
(Press Ctrl+g to toggle between English and the chosen language)
Post reply
Comments
Show Similar Question And Answers
QA->Five equal forces of 10 N each are applied at one point and all are lying in one plane. If angles between them are equal, the resultant of these forces wil be?....
QA->A train of length 150 meters took 8 seconds to cross a bridge of length 250 meters. Time taken by the train to cross a telephone post is....
QA->Hindustan on the Cross Road എന്ന കൃതി രചിച്ചത്?....
QA->Hindustan on the Cross Road എന്ന കൃതി രചിച്ചത് ?....
QA->It is more difficult to walk on a sandy road than on a concrete road because?....
MCQ->A pull of 20 t is suddenly applied to a road of cross-sectional area 40 cmThe stress produced in the rod is equal to:....
MCQ->A pipe of 0.1 m2 cross sectional area suddenly enlarges to 0.3 m2 cross-sectional area. If the discharge of the pipe is 0.3 m3 /sec, the head loss is....
MCQ->Consider the following statements : 1. In a member subjected to uniaxial tensile force the maximum normal stress is the external load divided by the maximum cross-sectional area. 2. When the structural member is subjected to uniaxial loading, the shear stress is zero on a plane where the normal stress is maximum. 3. In a member subjected to uniaxial loading, the normal stress on the planes of maximum shear stress is less than the maximum. Of these statements :....
MCQ->A 600 mm long and 50 mm diameter rod of steel (E = 200 GPa, α = 12 x 10-6/°C) is attached at the ends to unyielding supports. When the temperature is 30°C there is no stress in the rod. After the temperature of the rod drops to - 20°C, the axial stress in the rod will be....
MCQ->For double angles carrying tension, placed back to back and connected to either side of the gusset plate, the sectional area of the section, is equal to cross sectional area of....
×
×
Type The Issue
×
Your Marks
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use | Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...
Privacy
|
Terms And Conditions
Question ANSWER With Solution