Toggle navigation
Home
KPSC Previous Question Papers
Article Category
kerala psc
upsc
General
Popular Pages
Multiple Choice Question in കറന്റ് അഫയേഴ്സ് മേയ് 11
Multiple Choice Question in കറന്റ് അഫയേഴ്സ് - ഏപ്രില് 07
Multiple Choice Question in current-affairs-2016-12-22
Multiple Choice Question in current-affairs-2017-01-22
Multiple Choice Question in biochemistry-structure-and-properties-of-peptides
Multiple Choice Question in കറന്റ് അഫയേഴ്സ് - ക്വിസ് | ഡിസംബര് 05 - 12
Multiple Choice Question in biochemical-engineering-fluid-flow
Multiple Choice Question in biochemistry-allosteric-effects
Multiple Choice Question in current-affairs-2017-05-07
Multiple Choice Question in കറന്റ് അഫയേഴ്സ് മേയ് 26
Question Answer Bank
Multiple Choice Question Bank
Question Answer Category
Multiple Choice Question Category
Home
->
Multiple Choice Questions
Question Set
civil engineering steel structure design
1. If the slenderness ratio is greater than 160, the allowable stress in axial compression is multiplied by a factor (1.2 - (l/xy) where x is
(A): 1000
(B): 200
(C): 400
(D): 600
(E): 800
Previous Question
Show Answer
Next Question
Add Tags
Report Error
Show Marks
Ask Your Doubts Here
Type in
(Press Ctrl+g to toggle between English and the chosen language)
Post reply
Comments
Show Similar Question And Answers
QA->In Kiran’s opinion, his weight is greater than 65 kg but less than 72 kg. His brother does not agree with Kiran and he thinks that Kiran’s weight is greater than 60 kg but less than 70 kg. His mother’s view is that his weight cannot be greater than 68 kg. If all are them are correct in their estimation, what is the average of different probable weights of Kiran?....
QA->The ratio of bases of a cylinder and a cone are in the ratio 3: Volume of cylinder and cone are in the ratio 9: then their heights are in the ratio?....
QA->R is taller than X, but shorter than Z, Q is taller than Z, Y is taller than X, but shorter than R, Who is the shortest?....
QA->A man on tour travels first 160 km at 64 km/hr and the next 160 km at 80 km/hr. The average speed for the first 320 km of the tour is?....
QA->In an examination of mathematics Rajesh obtained more marks than the total marks obtained by Rahim and Sabu. The total marks obtained by Rahim and Saji was more than the Rajesh’s. Rajesh obtained more marks than Saji, Reenu obtained more marks than Rajesh. Who amongst them obtained the....
MCQ->If the slenderness ratio is greater than 160, the allowable stress in axial compression is multiplied by a factor (1.2 - (l/xy) where x is....
MCQ->If the slenderness ratio of a column is more than 160, the compressive stress obtained by the secant formula is multiplied by a factor in which value of x is....
MCQ->Consider the following statements : For an over-reinforced (singly reinforced) rectangular RC section. 1. the lever arm will be less than that for a balanced section. 2. the maximum stress developed by steel would equal the allowable stress in steel. 3. the maximum stress developed by concrete would equal allowable stress in concrete. Of these statements :....
MCQ->The design stress, which is more than the damaging stress, is the least unit stress that will render a member unfit for service before the end of its normal life. The design stress factor or factor of safety indicates the margin between design stress and the __________ stress.....
MCQ->Consider the following statements pertaining to a pile group and a single pile at failure : 1. In loose and medium dense sands, the failure load per pile in a group will generally be greater than the failure load for a single pile. 2. In cohesive soils, the failure load per pile in a group will be greater than failure load for a single pile. 3. For piles driven in dense sands, the failure load per pile in a group is greater than the failure load for a single pile. 4. When the pile spacing is greater than 10 times the pile diameter, the failure loads per pile in a group and forly same in both sands and clays. Of these statements :....
×
×
Type The Issue
×
Your Marks
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use | Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...
Privacy
|
Terms And Conditions
Question ANSWER With Solution