Question Set

1. You need to create an access list that will prevent hosts in the network range of 192.168.160.0 to 192.168.191.0. Which of the following lists will you use?





Ask Your Doubts Here

Type in
(Press Ctrl+g to toggle between English and the chosen language)

Comments

  • By: guest on 02 Jun 2017 01.57 am
    The range of 192.168.160.0 to 192.168.191.0 is a block size of 32. The network address is 192.168.160.0 and the mask would be 255.255.224.0, which for an access list must be a wildcard format of 0.0.31.255. The 31 is used for a block size of 32. The wildcard is always one less than the block size.
Show Similar Question And Answers
QA->Correct sentences among the following are: ) The tea is too hot that I cannot drink (2) Work hard, lest you should miss the chance (3) Unless you study well, you will fail (4) Unless you study well, you will pass....
QA->State list, Union list, Concurrent list are included in which of the following schedule....
QA->State list, Union list, Concurrent list are included in which of the following schedule....
QA->A man on tour travels first 160 km at 64 km/hr and the next 160 km at 80 km/hr. The average speed for the first 320 km of the tour is?....
QA->When data changes in multiple lists and all lists are not updated, this causes–....
MCQ->The Corporate router receives an IP packet with a source IP address of 192.168.214.20 and a destination address of 192.168.22.3. Looking at the output from the Corporate router, what will the router do with this packet? Corp#sh ip route [output cut] R 192.168.215.0 [120/2] via 192.168.20.2, 00:00:23, Serial0/0 R 192.168.115.0 [120/1] via 192.168.20.2, 00:00:23, Serial0/0 R 192.168.30.0 [120/1] via 192.168.20.2, 00:00:23, Serial0/0 C 192.168.20.0 is directly connected, Serial0/0 C 192.168.214.0 is directly connected, FastEthernet0/0....
MCQ->You have the following routing table. Which of the following networks will not be placed in the neighbor routing table? R 192.168.30.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0 C 192.168.40.0/24 is directly connected, Serial0 172.16.0.0/24 is subnetted, 1 subnets C 172.16.30.0 is directly connected, Loopback0 R 192.168.20.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0 R 10.0.0.0/8 [120/15] via 192.168.40.1, 00:00:07, Serial0 C 192.168.50.0/24 is directly connected, Ethernet0....
MCQ->You need to create an access list that will prevent hosts in the network range of 192.168.160.0 to 192.168.191.0. Which of the following lists will you use?....
MCQ->You are working with three networks that have the network IDs 192.168.5.0, 192.168.6.0, and 192.168.7.0. What subnet mask can you use to combine these addresses into one?....
MCQ->You install the Routing and Remote Access service on a Windows 2000 Server computer in your network. Your network is not directly connected to the Internet and uses the private IP address range 192.168.0.0. When you use Routing and Remote Access to dial in to the server, your computer connects successfully, but you are unable to access any resources. When you try to piiig servers by using their IP addresses, you receive the following message: "Request timed out." When you run the ipconfig command, it shows that your dial-up connection has been given the IP address 169.254.75.182. What should you do to resolve the problem?....
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use | Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions
Question ANSWER With Solution